Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL GTX™ Resin GTX6009 - Asia - (PPE+PA*) - Saudi Basic Industries Corporation (SABIC)

Check here, which other Noryl GTX datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

NORYL GTX™ 6009 resin is a non-reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade exhibits high heat resistance, and excellent chemical resistance. NORYL GTX6009 resin may be an excellent candidate for exterior automotive applications such as wheel covers and wheel trim.

Processing/Physical Characteristics	Value	Unit	Test Standard
ISO Data
Thermal conductivity of melt	0.23	W/(m K)	-
Spec. heat capacity of melt	1780	J/(kg K)	-
Ejection temperature	187	°C	-

Mechanical properties	Value	Unit	Test Standard
ASTM Data
Tensile Strength at Yield	53	MPa	ASTM D 638
Elongation at Break	90	%	ASTM D 638
Flexural Modulus	2130	MPa	ASTM D 790
Rockwell Hardness	R 110	-	ASTM D 785
Izod Impact notched, 1/8 in	736	J/m	ASTM D 256

Thermal properties	Value	Unit	Test Standard
ISO Data
Coeff. of linear therm. expansion, parallel	81.2	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion, normal	81.6	E-6/K	ISO 11359-1/-2
ASTM Data
DTUL @ 66 psi	160	°C	ASTM D 648

Electrical properties	Value	Unit	Test Standard
ASTM Data
Volume Resistivity	>1E15	Ohm*cm	ASTM D 257

Other properties	Value	Unit	Test Standard
Density	1120	kg/m³	ASTM D 792

Processing Recommendation Injection Molding	Value	Unit	Test Standard
Pre-drying - Temperature	95 - 105	°C	-
Pre-drying - Time	3 - 4	h	-
Processing humidity	≤0.07	%	-
Melt temperature	280 - 305	°C	-
Mold temperature	75 - 120	°C	-
Zone 1	265 - 305	°C	-
Zone 2	270 - 305	°C	-
Zone 3	275 - 305	°C	-
Screw speed	20 - 100	rpm	-
Back pressure	0.3 - 1.4	MPa	-

Diagrams

Characteristics

Processing

Injection Molding

Applications

Automotive

Regional Availability

Asia Pacific

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.